Wall mounted Fiber optic Rack for front mounted equipment, with retracted installation. It is produced in aluminium ensuring low weight and simple transport. It has profiles with slide rails that allows continuous height adjustment of nut and screw when installing equipment. Delivered flat-packed, so that one person can easily carry and mount the rack alone. Flexi Rack 19", B600xH500xD500, wall mount.
The Flexi Rack series is available in 19" design in standard heights 1800, 2000 and 2200 mm. Other widths and heights, as well as ETSI section width, can be supplied on request. The Flexi Rack series can also be supplied with side organizers for optimal fiber patch routing. The racks series offer high termination capacity.
This racks is designed so that the front plate of the equipment can optionally be mounted 12 to 15 cm offset from front line of the rack. This to protect front mounted connectors.
- For wall-mounting
- Extra 19 '' profiles to avoid front mounting
- Aluminum frames
- Width: 1 section, 600 mm
- Accessories available: cable trays, guide bars, legs, etc.
Cable ladder used for fastening cables and tubes to the rack.
Cable ladder used for fastening cables and tubes to the rack.
Shelf for network equipment that cannot be screwed directly into data or fiber rack or cabinet. The shelf has holes for better ventilation.
Shelf for network equipment that cannot be screwed directly into data or fiber rack or cabinet. The shelf has holes for better ventilation.
Shelf retractable for network equipment that cannot be screwed directly into data or fiber rack or cabinet. The shelf has holes for better ventilation.
Screw with spring nut for FR racks. The spring nut can be adjusted continuously height-wise in the rack.
Bend limiter for avoiding sharp bends on fiber optic patch cords in rack. Bend diameter 30 mm
Bend limiter for avoiding sharp bends on fiber optic patch cords in rack.
Guide to be placed in the middle of the vertical cord guide to keep the patch cords together.
Large brackets for sliding equipment onto. Fasten one on each sidewall in the racket.
Routing guide used on fan-out units to avoid that weight creates sharp bends or cord stress, may also be used to separate some patch cords from the rest.
Cable distributor used to separate the fibre-tubes in large cables to terminate them in different fiber optic panels.
Bend limiter for mounting on the top of the rack. Offload patch cords which must be guided over the top.
Angled bracket for mounting cable ladders and other equipment in racks.
Recently viewed
Wall mounted Fiber optic Rack for front mounted equipment, with retracted installation. It is produced in aluminium ensuring low weight and simple transport. It has profiles with slide rails that allows continuous height adjustment of nut and screw when installing equipment. Delivered flat-packed, so that one person can easily carry and mount the rack alone. Flexi Rack 19", B600xH500xD500, wall mount.
Fiber optic pigtail for terminating cables with splicing with SC connector. Sold in 12 pack
Fiber optic module delivered complete with 1:16 splitter terminated in LC/PC connectors. The modules are inserted in a 1U or 3U panel. The 3U panel may be populated with up to 12 modules, the 1U panel with up to 3 modules, and they may be placed in any order in the panel.
Fiber optic adapter E2000 DPX for single mode PC‐polished E2000‐connectors. Compatibility: IEC 61754‐15
Hybrid fiber optic connector used for give both power and data. Singelmode 1 m cable with MIL83526 DM4 - LC/PC. IP class IP68 rated. This hybrid connector is typically used for give both power and data connection to antennas and cameras.
Fiber optic subscriber cable with 2xLC/PC connectors with 0.9 mm ending. For wideband cabling for use in private homes.
Fiber optic adapter Duplex LC for multi mode LC‐connectors (OM1-62.5/125μm and OM2-50/125μm). Compatibility: IEC 61754‐20
ProBeam ruggedized connectors for optical communication in rough environments within defense and industry. Singlemode tactical cable with 4 channel ProBeam Jr. plugs in each end. Probeam connectors are hermaphroditic so cables can be daisy chained.
Single mode attenuated patch cord with MU/PC-MU/PC connector. Attenuation from 1 to 20 dB, diameter is 2.0 mm and standard length is 1 m.
AICI is a steel wire braided armored fiber optic cable designed for industrial and offshore applications. This cable meets fire safety requirements and can be used both indoors and outdoors. The cable features a weather-resistant outer sheath that can also withstand exposure to mineral oils and diesel over short periods.
Fiber optic adapter Duplex E2000 APC DPX adapter for single mode APC‐polished E2000‐connectors. Compatibility: IEC 61754‐15
Fiber optic patch panel 1.5U black with pre-assembled single mode SC/APC adapters. The panel has a drawer that ensures simple assembly and later maintenance of cables and connectors. The panel may be delivered for most optical interfaces and have a capacity of up to 96 LC connectors.